Nuc-Wipes

(1 review) Write a Review
SKU:
NW300
Size:
PK100
  • NUC-WIPES
  • NUC-WIPES
£57.20

 Select your currency from the header

Description

Order Nuc-Wipes from National Diagnostics by email to eu@genprice.com or us@genprice.com.

  • Completely Dissolving Wipes for Environmental Tests
  • Greater Counting Efficiency
  • Increased Reliability
  • Safe and Easy to Use
Catalog number: NW-300
Nuc-Wipes are dissolvable pads which assure superior environmental wipe tests. Nuc-Wipes are completely soluble in any scintillation solution, and because Nuc-Wipes dissolve completely, no emitted beta ray can be hindered or absorbed by an undissolved portion of the wipe. Nuc-Wipes allow full 4π counting efficiencies, thereby eliminating the possibility of lost counts due to absorption of beta rays by the filter itself.
Using intact filters for environmental wipe tests can give inaccurate, erratic results. Beta rays originating from particles on intact filters are attenuated and absorbed by the filter. Furthermore, depending on the relative affinity of the material for the solution, as material leaves the filter for the solution, counts change over time.
Nuc-Wipes eliminate the dependence of results on the direction of the filter paper and time. Because Nuc- Wipes dissolve in scintillation fluid, there is no intact filter to absorb or attenuate beta emissions. 4π counting efficiency is achieved, giving reproducible results.
 

Wipe Test Protocol:
The following protocol is intended as a helpful resource. Your Radiation Safety office may require special procedures not included in this method.

  1. Create a detailed floor plan of the laboratory of the work area and equipment for monitoring including bench tops, protective bench paper, shields, pipetmen, door handles, clothing, etc. as well as all devices or apparatus used in radionuclide work.
  2. Mark locations to be tested on a dated copy of the floor plan. Use a simple alphanumeric code to uniquely identify each location on the map.
  3. Using a system of labels corresponding to your alphanumeric code, label a 20ml scintillation vial to correspond to each wipe location.
  4. Label an additional vial for use for the background count.
  5. Use a Nuc-Wipe moistened with 65% – 75% ethanol to wipe each area to be tested. Wipe an area approximately of 100 cm2 applying moderate pressure. Because consistency in wipe technique is essential for reliable results, we recommend wiping with the same, easily repeatable pattern at each location.
  6. Place the wipe in the corresponding labelled scintillation vial and allow to air dry. Repeat process for each location to be monitored.
  7. Place a clean Nuc-Wipe in vial labelled for background determination.
  8. Add 10ml of emulsifying scintillation fluid to each vial. (For this application we recommend National Diagnostics Ecoscint H (LS-275), which combines high counting efficiency, biodegradability, and the capability to emulsify or dissolve both polar and nonpolar residues.) Agitate for 5 minutes or until Nuc-Wipes have completely dissolved.
  9. Measure the radioactivity on each wipe using a liquid scintillation counter. Record the results in the manner preferred by your Radiation Safety office.
  10. Decontaminate any areas that are determined to be contaminated with radioactivity, then rewipe. Decontaminate the area(s) until the measured levels are below guidelines.

 

View AllClose

1 Review

  • 5
    NUC-WIPES

    Posted by National Diagnostics on 11th Jun 2021

    Nuc-Wipes are dissolvable pads which assure superior environmental wipe tests. Nuc-Wipes are completely soluble in any scintillation solution, and because Nuc-Wipes dissolve completely, no emitted beta ray can be hindered or absorbed by an undissolved portion of the wipe. Nuc-Wipes allow full 4π counting efficiencies, thereby eliminating the possibility of lost counts due to absorption of beta rays by the filter itself.

View AllClose